Do you support free (homemade), an output device?

  • I tried to plug Tratek 232DMX50 232DMX250 On DMXControl 2.11 but it gave an error.
    ----------------------------------------------------------------------
    Das Plugin If32.out.dll implementiert die Klasse IDMCPlugin.
    The plugin is not compatible with this version of DMXControl.
    ----------------------------------------------------------------------
    Do you support free (homemade), an output device?

    I am the author of the project Twinkling Plug. This project supports 30 channels (10 RGB channels ).

    I plan to expand to 250 channels and support protocol DMX512.
    But I could not find on your site to the API plug-ins.

    Do you support free (homemade), an input device?

    How much support analog values to input your program?
    In the setting of the joystick saw only 4 axes.

    Is it possible to connect a full panel of 44 analog values??, and 20 buttons?

  • To enter data from home-made remote it can be connected via home-made USB - MIDI device.
    This part of the problem solved.

    The forum someone there?
    Where can I read about the API plugin DMX-Output?

    That which is, of the free, does not work.
    (Tratek 232DMX50 232DMX250 On DMXControl 2.11)

  • Our project "Twinkling Plug" is still evolving.
    main page http://paintpack.ru/
    HowTo, Home made http://www.mindrunway.ru/HWUsb2.html
    and we would like to create a plug-in to your program.
    IF example is lost (without example), how to create a plugin?
    All plug-ins created by the old source code compatibility cause an error.
    If you have lost it, even with time, a very good chance that he is old and not working now.
    ----------------------------------------------------------------------
    Das Plugin If32.out.dll implementiert die Klasse IDMCPlugin.
    The plugin is not compatible with this version of DMXControl.
    ----------------------------------------------------------------------

  • Good morning,


    I've developed this Delphi-7-Demoplugin years ago, but it was not working well. With Delphi7 you will not have access to the DMXControl-messagesystem and you are only able to send and receive DMX512 values to and from DMXControl. During an update I've removed the DMXControl-sourcecodes, because it was not helpful anymore.

    So the only working solution to use Delphi 7 plugins without restrictions was the following:

    • use a native VisualBasic 6 plugin for DMXControl as a kind of "DLL-Loader".
    • so DMXControl will use a nativ VB6 plugin, but this VB6 plugin will load a second dll - programmed in Delphi or VisualC++.

    Long ago in 2008 I've programmed a pluginloader, which was able to load the plugins of my own DMX-Software called "PC_DIMMER". I've attached a beta-version of the code. Maybe someone with a VB6-compiler can compile it for you - I don't have a compiler for VB6 anymore. You can use this as an API-reference to use delphi-plugins with the pluginloader: PC_DIMMER Wiki and Plugindevelopment (German) . Here is a google-translated version of this page: Plugindevelopment (English) .

    If you want to send values, you only have to call the following functions:

    Code
    DLLCreate(0,0,0,0,0); // will create the forms within the dllDLLStart; // will start the plugin
    Code
    DLLSendMessage(14, CHANNEL, VALUE); // will send data to the dll
    Code
    DLLConfigure; // will open a configuration-window
    Code
    DLLDestroy; // frees all forms and shutdown the plugin

    All other functions are for advanced usage.


    cu,
    Chris

  • Good morning,

    I've developed this Delphi-7-Demoplugin years ago, but it was not working well. With Delphi7 you will not have access to the DMXControl-messagesystem and you are only able to send and receive DMX512 values to and from DMXControl. During an update I've removed the DMXControl-sourcecodes, because it was not helpful anymore.

    And we all like a fairy tale: the more I learn => than more frightening.

    Project DMXControl is still developing?

    Or do we choose the dead program?


    use a native VisualBasic 6 plugin for DMXControl as a kind of "DLL-Loader".

    I do not have

    VisualBasic 6

    And easy send DMX to local IP with UDP packet, after receive it, and transmit to device.

    Then raise a more important topic:

    This program normally supports MIDI keyboard?

    is it possible to identify the analog resistance and buttons for easy control of preset DMX channels?

    I already did an usb device (i development IgorPlug2 - HID realise), but not made the keyboard, there are a lot of the ADC (48).

    Edited once, last by Hoc (June 29, 2012 at 3:06 PM).

  • DMXControl is not dead at all. But it is developed in the sparetime and because of that other stuff will allways have priority (e.g. family, etc.). Version 2 is written in vb6. So, if you want to create a working plugin with the current version you will have to write vb6 code. There are other ways for sure but this would be the easiest way.

    Midi is fully supported and can be used to control faders and other stuff. I personally use two Behringer BCF-2000 with motorized faders over midi to control my shows. But the BCF-2000 is a hardware controller and if I understood you right, you will calculate the midi values within a software and then send it to dmxcontrol. In this case, you will have use a virtual midi cable that is connected to the input in dmxcontrol and connected to the output of your midi sender software. So you will be able to pass in any midi value generated by another software.

    hope this helps

    Greets
    Phips

  • There are other ways for sure but this would be the easiest way.

    Easiest way:

    If you do not know how to write support for third-party plug-ins ...
    Send DMX packet, with UDP packet from local IP address.
    And any program written in any language may be to accept it.


    and if I understood you right, you will calculate the midi values within a software and then send it to dmxcontrol.

    I want to do a home made hardware MIDI controller (On AVR micro)
    There is a ready-made prototype of the device
    http://bascom.at.ua/publ/usb_midi_…ual_dj/1-1-0-52

    I plan to complicate the device. Set three processors to poll the ADC ports, one for command and control,
    and one for communication with USB. From the old dead hardware DMX controller make a hardware MIDI keyboard.

    In the third stage of design, if the first two will be successful, it will fully autonomous hardware DMX.
    With ability to connect to computer (USB Midi and USB DMX)

    It is not difficult, compared to my project "Twinkling Plug"...

    Edited once, last by Hoc (June 29, 2012 at 3:09 PM).

  • Hi QuickWitted,

    I have a working solution for you: extract the content of the attached ZIP-File to: c:\Program Files\DMXControl\

    Within the ZIP-File:

    • pc_dimmer2008.out.dll (this is the Pluginloader I have written years ago - still working)
    • if32.dll (the DLL for the tratek interface)
    • Tratek_232DMX50_232DMX250.dll (the PC_DIMMER Interface-Plugin for the Tratek)

    Make shure, that you extract the file "Tratek_232DMX50_232DMX250.dll" into the subfolder called "pc_dimmer_plugins" within the DMXControl-folder. The other two files have to be placed, where the "DMXControl.exe" is.


    After extacting the files, do the following:

    • please start DMXControl
    • go to "Outputplugins"
    • activate the "PC_DIMMER2008 Pluginloader"
    • click on the button "Configure selected Plugin" (the PC_DIMMER-Dialog will open)
    • select the "Tratek 232DMX50/232DMX250" plugin out of the dropdown-box
    • choose one of the two "Sendemethode". I guess no. 2 was the correct one - but I'm not shure - too long ago since I used it :rolleyes:
    • click on "Konfigurieren" and it will show up the dialog for the tratek

    Good luck,
    Chris

  • Thank you for your help.
    At the moment, got all to get started.
    We develop the design boards for DMX compatibility of current devices ("Twinkling Plug") to the DMX standard.
    The following week, after writing the software to the microprocessor system will check the plugin to work with our system.

    PS: IF add to the system has a microprocessor and a network interface card ("Art-Net", not UDP packets processing software on your computer) then find little benefit.

    It is much easier to take the data from the plugin ("Tratek 232DMX50/232DMX250") on a virtual RS232 port. You can accept the data as the program in a virtual RS232 on your program. And you can accept the data in a virtual RS232 on the USB bus (CDC device) and processed in the microprocessor.

  • I have a working solution for you:


    Thank you again.
    I was able to create its own set of emulating Velleman k8062
    Today I created a test firmware for my project Twinkling Plug
    On the program DMXStudio64 get 30 channels to control the project Twinkling Plug.

    But now the three questions.
    1) how to register my interface. That is, send a description of my functions with my Dll (Velleman k8062 initially not entirely successful in architecture).
    2) Do you have a step by step instruction? A better video how to use. In DMXStudio64 simple, and dmxcontrol all very complicated.
    3) Why use video on the site does not display dmxcontrol professional use? In the theater, for example? If you want to finalize the draft, I can shoot video in the theater ...

  • Newly created posts will remain inaccessible for others until approved by a moderator. The last reply was more than 365 days ago, this thread is most likely obsolete. It is recommended to create a new thread instead.